Home-automation HOME AUTOMATION User Manual Page 43
- Page / 98
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Status
The Status function is used to display the status of various items in the system. To enter the status menu, from the top-level
display or the main menu, press the 6 (STATUS) key on the console keypad.
STATUS
1=CTRL 2=ZONE 3=SUN ↓
4=TEST 5=TEMP 6=ENERGY
↑
1 = CTRL (CONTROL UNITS)
The Control Status menu allows you to view and scroll through the status of each control unit and to configure HLC and UPB
devices. To enter the Unit menu, from the Status menu, press the 1 (CTRL) key in the console keypad. The system will display:
DEN LAMP
STATUS OFF
↓
You may enter a unit number to start displaying the status of that unit, or simply press the down arrow key to scroll through the
list of units. The status display is as shown under Control, except that now the arrow keys may be used to continue scrolling
between units.
Porch Light 00:24:19
LAST COMMANDED ON
↓
You can also check the state and (if any) the remaining time duration of any Unit.
At this point, you may press the ' # ' key to control the unit as specified under Controlling Units or press ' # # ' to configure and
HLC or UPB device.
Note: Only HAI manufactured UPB™ devices (collectively referred to as HLC devices) can be configured using an Omni IIe
controller. Other UPB™ devices may be used, but cannot be configured using the Omni IIe controller; they must be configured
using a PC running the UPB™ UPStart configuration software.
Configuring HLC Devices
HLC devices can be configured using an Omni console or OmniTouch touchscreen connected to the Omni IIe controller. When
configuring HLC devices, the following information is programmed into the HLC device:
¾ Network ID (UPB Network ID configured in Omni IIe controller)
¾ Network Name (HAI Lighting)
¾ Unit ID (Unit Number of respective unit)
¾ Unit Name (which is the name description given to the respective unit in the Omni IIe controller)
¾ Room Name (using HLC, the name of the first unit in the respective group is used; otherwise the room number is used)
¾ Links (every device in each room is programmed with 6 consecutive Links, starting with Link 1; for example, every device
in Room 1 is programmed with Links 1-6, Room 2 is programmed with links 7-12, etc.)
¾ Other configuration information
When configuring HLC devices using an Omni console or OmniTouch touchscreen, each device (unit number) must first be
assigned a name in the Omni IIe controller. HAI recommends that you first configure your Omni IIe controller (naming all of the
HLC units) using the HAI PC Access Software, and then download the information to the Omni IIe controller.
Configuring HLC Devices using an Omni Console
To configure HLC devices from an Omni console, use the Status menu. To enter the Status menu, from the top-level display or
the main menu, press the 6 (STATUS) key on the console keypad.
STATUS
1=CTRL 2=ZONE 3=SUN ↓
Page 35
- Owner's Manual 1
- All Rights Reserved 2
- Contents 3
- INTRODUCTION 9
- OVERALL DESCRIPTION 10
- Normal Top-Level Display 11
- Display Menus 11
- Omni IIe Maintenance 13
- SECURITY SYSTEM OPERATION 14
- Using Shortcut Keys 15
- Restoring Zones 16
- Quick Arm 16
- Bypassing Zones 16
- Emergency Keys 18
- Alarm Reset 19
- Alarm Cancel 19
- Trouble Indications 20
- GOTO Area 22
- Testing Your System 23
- CONTROL 24
- About Lutron RadioRA 26
- About ALC 27
- About X-10 27
- House Codes 27
- Unit Numbers 28
- Scrolling Through Names 28
- Controlling Units 28
- Timed Commands 32
- Status of a Unit 32
- Internal Flags 32
- Controlling Outputs 33
- All On / Off 33
- Buttons 37
- Temperature Control 37
- HAI RC-Series Thermostats 38
- Temperature Alarms 42
- Humidity 42
- 1 = CTRL (CONTROL UNITS) 43
- 2 = ZONE 44
- Event Log 46
- Messages 47
- TELEPHONE CONTROL 50
- Alternate Method 51
- Main Menu 51
- 6 - Status 53
- 7 - Events 53
- 8 - Phone 54
- 9 - Good-Bye 54
- Emergency Dial-Out 55
- Digital Dialer 55
- Voice Dialer 55
- PC Access 57
- Local Network 58
- Local / Wide Area Network 59
- Set Up Codes 60
- Set Up Time 61
- Edit Programs 64
- Edit Programs When 65
- Button and Event Programs 66
- Corresponding Switch Table 67
- ANY TYPE ↓ 69
- Edit Program Command 71
- Edit Program Condition 74
- SELECT CONDITION: 76
- Set Up Dial 77
- Set Up Arming 79
- Set up Miscellaneous 80
- ↓), scroll to the 84
- Set Up Names 85
- Set Up Voice 86
- Set Up Address 86
- FIRE ESCAPE PLANNING 87
- INSTRUCTIONS TO CALLED PARTY 91
Related products and manuals for Furniture Home-automation HOME AUTOMATION
(3 pages)© 2020, manymanuals.com. All rights reserved. | 0.746 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals